Piece Kit
Piece Kit
 |
KitchenAid KPRA Pasta Roller Attachment for Stand Mixers
List Price:  |
DescriptionIf you have a passion for perfectly prepared pasta, try making your own delectable lasagna noodles, fettuccine, or linguine fini with this pasta roller set that fits all KitchenAid stand mixers. The three attachments include a pasta roller, a fettuccine cutter, and a linguine fini cutter... |
Installation Instruction for Hid Conversion Kits
HID Conversion Kits might be illegal in some states and are sold for off road or show use only. Check with your local BMV for more information.
Helpful Information and Installation Tips:
- Do not touch the HID bulb. If you do touch the bulb during installation, clean with alcohol.
- Do not look directly into the bulb when it is turned on as it may cause permanent damage to your eyes.
- Headlights must be properly adjusted after installation. HID bulbs are much brighter than halogen bulbs. By not adjusting your headlights, you may reduce the visibility of oncoming traffic due to glare. If you do not know how to adjust your headlights, please consult a professional.
- Do not drop or apply inappropriate/unnecessary force to your HID components as doing so may cause damage to them. If any damage is discovered, discontinue use and contact your retailer. Do not use the system until the problem is solved, in order to avoid possible electric-shock or fire.
- The HID system generates 23000volts when activated. Do not use wet or oily hands when installing or inspecting the system. Or you may be subjected to severe burns or electric-shock.
- Make sure all connectors and wires are secured and away from any hot surfaces. Wires that are loose or resting against a hot surface may cause electrical hazards.
- Do not turn on the bulb near flammable material when it is outside of headlight housing.
- Do not turn lights on/off rapidly. Doing so may reduce the lifespan of your bulbs.
- Do not install HID system in any housing with cracks. Moister may damage the bulb or cause electric-shock.
- Before final installation pre-test all the components. Ensure compatibility by plugging in all the wires and turning the system on.
Note: Special adapters, connectors, modules or harness may be needed to correctly install the HID system on some vehicles. Make sure you have everything needed for your vehicle. BMW, Mercedes, Audi, Dodge/Chrysler and Volkswagen are only a few that may need special installation materials.
Single Beam Installation Instructions:
- Verify that the HID Conversion Kit you received have all the component needed for the installation (A list of component available below)
- Disconnect the car battery.
- Remove the factory light bulbs. If your vehicle's headlights have dust caps, please remove them as well.
- If your vehicle is equipped with headlight dust caps, drill a 1"(24mm) hole to accommodate the wiring harness.
- Remove the xenon HID bulb from the protective casing. Be careful NOT to touch the bulb. Handle it by its plastic base. If any grease or dirt gets on the bulb wipe clean with rubbing alcohol.
- Put the bulb's wiring harness through the dust cap (as illustrated).
- Insert the xenon HID bulb into your headlight and secure it.
- Connect the spade terminals (positive & negative) to the factory headlight wiring harness.
- Insert the rubber boot (on the wiring harness) through the hole on the dust cap (which you drilled earlier).
- Connect the bulb to the ballast. The quick release will "click" once fully secured.
- Find a mounting location for the ballast. Use the ballast bracket, screws or zip-ties as needed. Note: Do not drill holes on the ballast box, mount away from moving components and mount to a secure location.
- Check your vehicle's headlight fuse. Make sure it is rated at 20amps or higher. Replace the fuse with a 20amp fuse if your headlight fuse is of a lower rating.
- Reconnect the battery cables.
- Turn light switch on and allow your new xenon light to run for 10 minutes.
Bi-Xenon Installation Instructions:
Wiring Diagram
- Verify that the HID Conversion Kit you received have all the component needed for the installation (A list of component available below)
- Clean all connectors and wipe the HID bulbs and connectors with rubbing alcohol
- Install the HID bulbs into the headlight housing
- Connect the HID bulbs to the ballast (2 round quick-disconnects)
- Connect the high beam control wires (small rectangular connectors)
- Connect the ballasts to the Hi/Lo wiring harness (oval connectors with yellow rubber seals)
- Connect the 3-pin socket on the wiring harness to ONE of the headlight sockets
- Connect the thick red wire to the battery positive
- Connect the thick black wires to the battery negative or ground
- Mount the ballast and clean up the wiring harness with zip ties
- Find a mounting location for the ballast. Use the ballast bracket, screws or zip-ties as needed. Note: Do not drill holes on the ballast box, mount away from moving components and mount to a secure location.
- Turn headlight switch on and allow your new xenon light to run for 10 minutes
Adjusting Your Low Beam Headlight:
- Park on a level surface 20 feet behind another car and turn on your low beam headlights.
- Make sure the cut-off of the beam is just above the bumper of the car in front. (Please refer to the image below)
- To make sure the two headlights are even adjusted, please turn on the headlights directly against a flat wall 20 feet away and adjust lights until the cut-offs of two headlight line up.
Troubleshooting:
Flickering during pre-test or bulb out warning: Some vehicles measure the resistance of the bulb connecting into the factory socket. Since the Xenon ballast does not use any resistance when lighting the bulbs, the vehicles computer thinks there is something wrong, when there really is not. It will then begin to flicker the HID kit and may display a bulb out warning. To remedy this, an automotive HID bulb out resistor must be used, or a bulb out warning module.
Single Beam HID Conversion Kit Components:
- HID Xenon Bulbs (with wires) Two (2) pieces
- HID Ballasts Two (2) pieces
- Bracket(s)/Screw(s)/Other Mounting Accessories One (1) set
- Installation Manual One (1) piece
Bi-Xenon HID Conversion Kit Components:
- HID Xenon Bi-Xenon Bulbs (with wires) Two (2) pieces
- HID Ballasts Two (2) pieces
- Hi/Low Beam Control Wiring Harness One (1) piece
- Bracket(s)/Screw(s)/Other Mounting Accessories One (1) set
- Installation Manual One (1) piece
***Some items may vary from one manufacturer to another***
This Installation guide is written for the HID Conversion Kits listed above. Some kits might require additional steps that are not listed here. Contact your supplier for more information.
About the Author
We provide the best quality
HID conversion kits in the US. Made in China with the latest German
Technology 9004, 9005,
9006,
9007, H1, H4 and
H7
Professor Amos Shock It Clean 4 Piece Kit
 |
 Canon Rebel T2i Digital SLR Camera 24 Piece Kit  US $1,360.40
|
 Canon EOS 7D Digital SLR Camera 24 Piece Kit US $2,415.40
|
 Nikon D3000 Digital Camera 18 Piece Kit US $649.99
|
 Canon EOS 60D Digital SLR Camera 24 Piece Kit US $1,884.40
|
 Nikon D90 Camera 28 Piece Kit w 3 Lenses and Filters US $1,494.95
|
 Canon EOS 60D Digital SLR Camera 22 Piece Kit US $1,859.45
|
 Canon EOS 7D Digital SLR Camera 22 Piece Kit US $2,736.65
|
 Canon EOS 7D Digital SLR Camera Loaded 20 Piece KIT US US $1,828.90
|
 Canon Rebel T3i Digital SLR Camera 22 Piece Kit US $1,145.24
|
| Powered by phpBay Pro |
|
KitchenAid KPRA Pasta Roller Attachment for Stand Mixers
List Price: |
DescriptionIf you have a passion for perfectly prepared pasta, try making your own delectable lasagna noodles, fettuccine, or linguine fini with this pasta roller set that fits all KitchenAid stand mixers. The three attachments include a pasta roller, a fettuccine cutter, and a linguine fini cutter... |
 |
Mastrad A64601 Top Chips Maker and Slicer Set
List Price: |
DescriptionMake your own delicious chips with the Topchips silicone charcoal chips maker and mandoline set. This set of chips maker and mandoline is made of highly durable microwave safe silicone that will cook the sliced potatoes into homemade chips in 3 to 5 minutes and the mandoline has a super sharp stainless steel blade... |
 |
EasyLunchboxes 3-compartment Bento Lunch Box Containers (Set of 4) BPA-Free. Easy-Open Lids (Not Leakproof)
Sale Price: $13.95 |
DescriptionSave time, money, paper, and plastic when you use EasyLunchboxes. No more wasteful baggies or mismatched plastic containers. Now you can pack lunches fast for work or school. Even make homemade "Lunchables®!" Created by a mom of three, these bento-style, 3-compartment containers are designed to be carried upright in the EasyLunchboxes cooler bag (choose from 7 vibrant colors)... |
 |
Neil Peart - Anatomy of a Drum Solo
List Price: |
DescriptionANATOMY OF A DRUM SOLO - DVD Movie |
 |
Outers Universal 62-Piece Blow Molded Gun Cleaning Kit
List Price: |
DescriptionOuters Univ 62Pc Blow Mld Cln Kit. 62-PIECE BLOW-MOLDED UNIVERSAL KIT : Latched hard plastic storage case with handle : Built-in custom parts organizer : Additional compartments to hold bottles of gun-cleaning chemicals : 3 solid brass rods for ... |
 |
Beecham Conducts Delius: The Complete Stereo Recordings
List Price: |
DescriptionSir Thomas Beecham enjoyed a career-long association with the music of Delius. As Grieg provided the encouragement to Delius to keep composing, Delius in turn helped Beecham choose conducting as his path... |
 |
SE 3 Pc. Power Extension Socket Bits for Drills
List Price: |
DescriptionAdd versatility to your power drills. 3pc Power Extension Socket Adaptor has Hex bit for all power drill chucks. Comes in 3 Sizes : 1/4 in. , 3/8 in. & 1/2 in.for your full range of sockets. |
 |
Leatherman 931014 40-Bit Assortment for Leatherman Bit Drivers
List Price: |
 |
Silverhill 20 Piece Tool Kit for Apple Products
Sale Price: $11.99 |
DescriptionNew from Silverhill Tools is a useful kit that helps with doing many of the routine tasks associated with Mac ownership, including accessing memory slots or opening housings. Includes 5 screwdrivers: Pentalobe size 1, Pentalobe size 5, flat, phillips, and Triwing... |
 |
Four Legged Chicken
Sale Price: $1.99 |
